Code Reader 1200 Manuel d'installation Page 146
- Page / 176
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
TC1200 REFERENCE MANUAL
134
5
5.2.2 Operating Mode
Operating Mode
Selects the scan operating mode for the reader. Selections:
On Line: the reading phase is defined as the time between the Phase ON and Phase OFF
events. The Phase events can be signals coming from the trigger button (or external
presence sensor connected to the scanner input for RS232 models).
Serial On Line: the reading phase is defined as the time between the Phase ON and Phase
OFF events. The Phase events are serial start/stop strings sent from the host over the serial
interface.
Automatic: The device does not require connections with external presence sensors in this
operating mode. In this mode the scanner is continuously scanning. The reading phase is
enabled when a barcode enters the reading zone of the scanner and is terminated after an N
number of scans without a code, where N is set using the Automatic Threshold selection.
The next reading phase will begin when a code enters the reading zone of the scanner
again. The N number of scans without a code must be selected to assure code identification
in the reading zone. Code transmission is identical to the other operating modes except that
there is no transmission on the serial port in the case of a No Read condition.
Automatic (Object Sense):The reader is normally in the Object Sense state (a low
power/ready-to-read condition). When an item is automatically detected in the reader’s field
of view, the Automatic operating mode is turned on. The Automatic Threshold assures code
identification. When objects are no longer present in the reading field, the Timeout ends
Automatic mode and returns the reader to the Object Sense state.
Test: The Test mode reports information about the reading performance of the scanner and
the code is continuously read. After 100 scans, the following information is transmitted on the
serial interface:
the code content
percentage of good reads (if the good read percentage is 0 no transmission is done)
The information can be displayed on the Host PC by running a terminal emulator program
(ex. Hyper Terminal). The output data format is fixed.
Automatic Threshold
For Automatic operating modes, the Automatic Threshold sets an N number of scans without
a code in order to assure code identification in the reading zone. Selection: a value from 2 to
255.
To set this value:
1. Determine the desired number of reads. (2-255).
2. Use the Chart in Appendix C to find the hex equivalent
for the desired numeric value.
3. Go to page 56 and scan the ENT
ER/EXIT PROGRAMMING MODE barcode to enter
Programming Mode.
4. Scan the barcode: SELECT AUTOMATIC THRESHOLD VALUE.
- Reference Manual 1
- CONTENTS 3
- REFERENCES 9
- FCC COMPLIANCE 10
- POWER SUPPLY 10
- CE COMPLIANCE 10
- HANDLING 11
- 1 INTRODUCTION 13
- 1.3 AVAILABLE MODELS 14
- 1.4 ACCESSORIES 15
- 2 INSTALLATION 16
- INSTALLATION 17
- 2.1.4 Electrical Connections 20
- RS232 Interface 21
- Outputs 23
- 2.2 TC1200 CCD SCAN ENGINE 24
- 2.2.2 Electrical Connections 25
- USB Interface 26
- TC1200 EXTERNAL TRIGGER 27
- OUT1/2 28
- 2.3 POSITIONING 29
- 3.1 TC1200 CONFIGURATION 34
- RS232 Models 34
- USB Models 34
- Command Syntax 35
- 4 BARCODE CONFIGURATION 52
- ËÄ$P,HA00,PmÂÎ 52
- ËÄ$P,HA05,PmHÎ 52
- ËÄ$P,HA47,PmtÎ 53
- ËÄ$P,HA35,Pm]Î 53
- ËÄ$P,HA2B,PmWÎ 53
- ËÄ$P,HA2C,Pm_Î 53
- GLOBAL INTERFACE FEATURES 55
- AUD RATE 56
- ATA BITS 56
- TOP BITS 56
- BAUD RATE 57
- DATA BITS 58
- STOP BITS 58
- RS232/USB-COM 59
- INTERCHARACTER DELAY 60
- DISABLE CHARACTER 60
- ENABLE CHARACTER 60
- ACK/NAK OPTIONS 60
- ACK CHARACTER 60
- NAK CHARACTER 61
- ACK/NAK TIMEOUT 61
- ACK/NAK RETRY COUNT 61
- ACK/NAK ERROR HANDLING 61
- USB-KBD 62
- KEYBOARD COUNTRY 63
- KEYBOARD COUNTRY (CONTINUED) 64
- KEYBOARD INTERCODE DELAY 64
- SEND CONTROL CHARACTERS 65
- USB KEYBOARD SPEED 65
- KEYBOARD SPEED (CONTINUED) 66
- ËÄ$CKBSP09mRÎ 66
- ËÄ$CKBSP0Am3Î 66
- READING PARAMETERS 67
- ILLUMINATION MODE 68
- OPERATING MODE 68
- AUTOMATIC THRESHOLD 68
- PHASE OFF EVENT 69
- TIMEOUT 69
- SERIAL START 69
- SERIAL STOP 69
- LED INDICATION 69
- LABEL PROGRAMMING MODE 70
- EXPOSURE MODE 70
- READING CONDITIONS 70
- DATA FORMAT 71
- DATA TRANSMISSION 72
- CODE VERIFIER MODE 72
- MATCH STRING 72
- WRONG CODE STRING 72
- CASE CONVERSION 73
- GLOBAL PREFIX 73
- GLOBAL SUFFIX 73
- NO READ STRING 73
- TRANSMIT AIM IDS 74
- TRANSMIT CUSTOM LABEL IDS 74
- CUSTOM LABEL IDENTIFIERS 74
- Enter/Exit Configuration 75
- Enter/Exit Configuration 76
- DIGITAL OUTPUTS 78
- OUTPUT 1 ACTIVATION EVENT 79
- OUTPUT 1 DEACTIVATION EVENT 79
- OUTPUT 2 ACTIVATION EVENT 80
- OUTPUT 2 DEACTIVATION EVENT 80
- POWER SAVE 81
- SLEEP MODE TIMEOUT 82
- CODE SELECTION 83
- CHECK CHARACTER TX 85
- EXPAND TO EAN-13 85
- NUMBER SYSTEM TX 85
- UPC-A MINIMUM READS 86
- EXPAND TO UPC-A 87
- UPC-E MINIMUM READS 88
- ISBN CONVERSION 89
- ISSN CONVERSION 89
- FLAG 1 CHARACTER 90
- EAN-13 MINIMUM READS 90
- EAN-8 MINIMUM READS 91
- ENABLE OPTIONAL P2 ADD-ON 92
- ENABLE OPTIONAL P5 ADD-ON 92
- P2 MINIMUM READS 92
- P5 MINIMUM READS 93
- OPTIONAL ADD-ON TIMER 93
- GTIN FORMAT 94
- IN-STORE MINIMUM READS 95
- CODE 39 95
- CODE 39 FULL ASCII 95
- CODE 39 CHECK TX 96
- CODE 39 START/STOP TX 96
- CODE 32 CHECK TX 97
- CODE 32 START/STOP TX 97
- Code 39 Check Options 98
- Code 39 Decoding Options 98
- QUIET ZONES 100
- STITCHING 100
- SET LENGTH 101
- CODE 128 101
- GS1-128 ENABLE 101
- CODE LENGTH CONTROL 101
- EXPAND TO CODE 39 102
- Code 128 Check Options 102
- CHECK TX 102
- FUNCTION CHARACTER TX 102
- SUB-CODE CHANGE TX 102
- Code 128 Decoding Options 103
- MINIMUM READS 103
- DECODING LEVEL 103
- CHARACTER CORRELATION 104
- ISBT 128 CONCATENATION 105
- CONCATENATION MODE 105
- INTERLEAVED 2 OF 5 106
- CHECK CALCULATION 107
- ZERO PATTERN 109
- STANDARD 2 OF 5 110
- INDUSTRIAL 2 OF 5 113
- CODABAR 116
- CODABAR ABC 117
- Codabar Check Options 118
- START/STOP SET 118
- START/STOP TX 119
- START/STOP MATCH 119
- Codabar Decoding Options 119
- INTERDIGIT RATIO 120
- CODE 11 122
- Code 11 Check Options 123
- Code 11 Decoding Options 124
- GS1 DATABAR OMNIDIRECTIONAL 126
- GS1 DATABAR EXPANDED 127
- COUPON CONTROL 128
- GS1 DATABAR LIMITED 129
- CODE 93 130
- Code 93 Check Options 131
- Code 93 Decoding Options 132
- MSI Check Options 135
- MSI Decoding Options 136
- PLESSEY 137
- Plessey Check Options 138
- Plessey Decoding Options 138
- 5 PARAMETER REFERENCES 140
- Intercharacter Delay 141
- Disable Character 141
- Enable Character 142
- ACK NAK Options 142
- ACK Character 143
- NAK Character 143
- ACK NAK Timeout Value 144
- ACK NAK Retry Count 144
- Keyboard Intercode Delay 145
- 5.2 READING PARAMETERS 145
- 5.2.1 Illumination Mode 145
- Illumination Mode 145
- 5.2.2 Operating Mode 146
- Operating Mode 146
- Automatic Threshold 146
- Phase Off Event 147
- Timeout 147
- Serial Start 148
- Serial Stop 148
- 5.2.3 Good Read LED 149
- LED Indication 149
- 5.2.4 Exposure Mode 149
- 5.2.5 Preset Recipes 149
- Reading Conditions 149
- 5.3 DATA FORMATTING 150
- 5.3.1 Global Prefix/Suffix 151
- No Read String 152
- 5.3.2 Code Identifiers 153
- Label IDs 153
- Label ID: Pre-loaded Set 153
- TC1200 REFERENCE MANUAL 154
- Global AIM ID 155
- 5.3.3 Code Verifier 156
- Match String 156
- Wrong Code String 156
- 5.4 DIGITAL OUTPUTS 157
- Activation Event 157
- Deactivation Event 157
- Deactivation Timeout 157
- Active Level 157
- 5.5 POWER SAVE 158
- Sleep Mode Timeout 158
- 5.6 CODE SELECTION 158
- Decoding Level 158
- Interdigit Ratio 159
- Character Correlation 159
- Minimum Reads 159
- Stitching 160
- Quiet Zones 160
- 5.6.1 Concatenation 160
- Concatenation Mode 160
- 5.6.2 Set Length 161
- Set Length 1 161
- Set Length 2 162
- 6 MAINTENANCE 163
- 7 TECHNICAL FEATURES 164
- 7.1 READING DIAGRAMS 165
- A DEFAULT PARAMETERS TABLE 166
- Transmit Labels in 168
- GS1-128 Data Format) 168
- C ASCII/HEX/DECIMAL CHART 172
- ASCII CHART 173
- D RESERVED CHARACTERS 174
- DECLARATION OF CONFORMITY 175
Produits connexes et manuels pour Lecteurs de codes-barres Code Reader 1200
COMPRO V600 - START UP GUIDE manuales
Manuales del propietario y guías del usuario para Carros COMPRO V600 - START UP GUIDE.
Ofrecemos 1 manuales en pdf COMPRO V600 - START UP GUIDE para descargar gratis por tipos de documentos: Especificaciones
Compro V600 - START UP GUIDE Especificaciones (286 paginas)
Marca: Compro | Categoria: Cars | Tamaño: 6.14 MB |
Tabla de contenidos
Alfa 147
2
PERSONAL
6
FRONT SEATS
19
REAR SEATS
22
ADJUSTMENTS
25
ADJUSTMENT
26
SEAT BELTS
29
AIR BAGS
39
A0A0012m
61
A0A0013m
61
A0A0007m
61
A0A0014m
61
New mission
74
CONTROLS
111
SELESPEED
115
TRANSMISSION
115
COMPARTMENT
132
ROOF RACK
137
PROVISION
137
HEADLIGHTS
138
PARKING SENSORS
140
VDC SYSTEM
143
ASR SYSTEM
145
EOBD SYSTEM
147
SOUND SYSTEM
148
PRESETTING
148
A0A1125m
154
A0A1126m
156
SPV E200, C500
178
QTEK 8020, S100
178
SOLUTION
182
PROBLEM SOLVING
182
REFUELLING
183
ENVIRONMENTAL
185
PROTECTION
185
STARTING
187
THE ENGINE
187
PARKING
190
FUEL ECONOMY
190
WINTER TYRES
192
COMFORT
192
SUSPENSIONS
192
SNOW CHAINS
193
CAR INACTIVITY
194
TOWING TRAILERS
194
Rear wheel axis
197
Centering hole
197
Regulation ball
197
EMERGENCY
198
IN AN EMERGENCY
199
CHANGING A WHEEL
202
FIX&GO KIT FOR
205
QUICK TYRE
205
REPAIRING
205
WHEN NEEDING TO
210
CHANGE A BULB
210
IF AN EXTERIOR
213
LIGHT GOES OUT
213
IF AN INTERIOR
219
LIGTH GOES OUT
219
IN THE EVENT
233
OF AN ACCIDENT
233
SCHEDULED
235
SERVICING
235
ADDITIONAL
238
OPERATIONS
238
PROGRAMME
238
CHECKING LEVELS
240
AIR CLEANER
247
POLLEN FILTER
248
A0A0393m
249
ELECTRONIC
251
CONTROL UNITS
251
WHEELS AND TYRES
252
WINDSCREEN/
253
RUBBER HOSES
253
BODYWORK
255
FUEL SUPPLY
262
SUSPENSION
263
STEERING SYSTEM
263
PERFORMANCE
267
DIMENSIONS
268
REFILLING
271
FUEL CONSUMPTION
274
EMISSIONS
274
INSTRUMENT
275
DASHBOARD
278
S E R V I C E
285
Más productos y manuales para Carros COMPRO
| Modelos | Tipo de documento |
|---|---|
| Ninguno |
© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels