Code Code Reader 1000 Spécifications Page 91
- Page / 140
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
81
Update
You may configure in which format the collected data will be output to the host computer.
Barcode read by the scanner will be processed in the following sequence –
1) Perform character substitution on the data scanned.
2) Add
Code ID and Length Code to the front of the data:[Code ID][Length Code][Data]
3) Process the whole data in step 2 with user formats. Data is now divided into fields by
user specified rules. Refer to
Chapter 5 Applying Formats for Data Editing.
4) Add
Prefix Code and Suffix Code before transmission:[Prefix Code][Processed
Data][Suffix Code]
IN THIS CHAPTER
4.1 Character Substitution................................................ 81
4.2 Prefix/Suffix Code...................................................... 83
4.3 Code ID.................................................................... 84
4.4 Length Code ............................................................. 88
4.1 CHARACTER SUBSTITUTION
Character substitution is performed on every occurrence of the first character specified. If
only one character is specified, every occurrence of that character in the barcode will be
taken away.
The first character will be replaced by the second character(s).
Up to three sets of character substitution can be configured.
Note: The character substitution is performed only on the barcode itself and before the
processing of editing formats. It is not applicable to the Prefix/Suffix Code, Code
ID, Length Code, or any Additional Field.
Chapter 4
DEFINING OUTPUT FORMAT
- Scanner 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 11
- INSIDE THE PACKAGE 12
- Introduction 13
- SYMBOLOGIES SUPPORTED 14
- QUICK START 17
- ENTER CONFIGURATION MODE 18
- EXIT CONFIGURATION MODE 18
- DEFAULT SETTINGS 19
- RESTORE SYSTEM DEFAULTS 19
- Quick Start 21
- Refer to Appendix III 23
- LIST THE CURRENT SETTINGS 24
- Chapter 1 25
- 1.3.1 GOOD READ BEEP 27
- 1.3.2 FREQUENCY 27
- 1.4 SCAN MODES 28
- Chapter 1 29
- 1.5 SCANNING TIMEOUT 32
- Laser mode 32
- Auto Off mode 32
- Auto Power Off mode 32
- 1.9 NEGATIVE BARCODES 35
- Chapter 2 37
- 2.1 KEYBOARD WEDGE 38
- Chapter 2 39
- Selecting Output Interface 39
- 2.1.2 KEYBOARD SETTINGS 40
- 2.1.3 INTER-CHARACTER DELAY 48
- 2.2 RS-232 49
- 2.2.2 BAUD RATE 49
- 2.2.3 DATA BITS 50
- 2.2.4 PARITY 50
- 2.2.5 FLOW CONTROL 51
- 2.2.6 INTER-CHARACTER DELAY 51
- 2.3.3 BAR STATE 53
- 2.3.4 MODULE TIME 53
- 2.3.5 MARGIN TIME 54
- Chapter 3 55
- 3.1 CODABAR 56
- 3.1.3 CLSI CONVERSION 57
- 3.2 CODE 25 – INDUSTRIAL 25 58
- 3.2.2 VERIFY CHECK DIGIT 59
- 3.2.3 TRANSMIT CHECK DIGIT 59
- 3.3 CODE 25 – INTERLEAVED 25 61
- 3.3.2 VERIFY CHECK DIGIT 62
- 3.3.3 TRANSMIT CHECK DIGIT 62
- Chapter 3 63
- Changing Symbology Settings 63
- 3.4 CODE 25 – MATRIX 25 64
- 3.4.2 VERIFY CHECK DIGIT 65
- 3.4.3 TRANSMIT CHECK DIGIT 65
- 3.5 CODE 39 67
- 3.5.2 VERIFY CHECK DIGIT 68
- 3.5.3 TRANSMIT CHECK DIGIT 68
- 3.6 CODE 93 69
- 3.7 CODE 128 69
- 3.8 EAN-8 70
- 3.8.1 CONVERT TO EAN-13 71
- 3.8.2 TRANSMIT CHECK DIGIT 71
- 3.9 EAN-13 72
- 3.9.1 CONVERT TO ISBN 73
- 3.9.2 CONVERT TO ISSN 73
- 3.9.3 TRANSMIT CHECK DIGIT 73
- 3.10.1 TRANSMIT CODE ID 74
- 3.10 GS1-128 (EAN-128) 74
- 3.11 MSI 75
- 3.11.1 VERIFY CHECK DIGIT 75
- 3.11.2 TRANSMIT CHECK DIGIT 75
- 3.12 FRENCH PHARMACODE 77
- 3.12.1 TRANSMIT CHECK DIGIT 77
- 3.13 ITALIAN PHARMACODE 78
- 3.13.1 TRANSMIT CHECK DIGIT 78
- 3.14 PLESSEY 79
- 3.14.1 CONVERT TO UK PLESSEY 79
- 3.14.2 TRANSMIT CHECK DIGIT 79
- GS1 DataBar Expanded 83
- 3.16 TELEPEN 85
- 3.17 UPC-A 86
- 3.17.1 CONVERT TO EAN-13 87
- 3.17.3 TRANSMIT CHECK DIGIT 87
- 3.18 UPC-E 88
- 3.18.4 TRANSMIT CHECK DIGIT 90
- Chapter 4 91
- 4.3.2 CHANGE CODE ID 96
- 4.3.3 CLEAR CODE ID SETTINGS 97
- 4.4 LENGTH CODE 98
- User Guide 100
- Chapter 4 101
- Defining Output Format 101
- Chapter 5 103
- 5.1.2 EXCLUSIVE DATA EDITING 105
- 5.2.2 RESTORE DEFAULT FORMAT 108
- 5.3.1 APPLICABLE CODE TYPE 109
- 5.3.2 DATA LENGTH 113
- 5.4.1 TOTAL NUMBER OF FIELDS 115
- 5.4.2 FIELD SETTINGS 116
- 107 117
- Field 2 Setting 117
- 109 119
- Field 4 Setting 119
- 111 121
- Additional Fields 121
- Key Type Key Status 121
- 113 123
- 5.6 PROGRAMMING EXAMPLES 124
- 5.6.1 EXAMPLE I 124
- SPECIFICATIONS 127
- 1100, 1105 129
- Appendix I 131
- EXAMPLE 132
- Appendix II 133
- KEY TYPE & STATUS 134
- KEY TYPE 134
- KEY STATUS 134
- Appendix III 137
- HEXADECIMAL SYSTEM 138
- ASCII TABLE 139
Produits connexes et manuels pour Lecteurs de codes-barres Code Code Reader 1000
(17 pages)
(15 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels